Skip to main content

Pattern #1 - Basic Tatted Edging

 Main Pattern

This is a pretty basic tatting pattern. Variations similar to this can be found all over the Internet and in almost every book on tatting. Below are some additional ideas of how you can use the basic pattern to create your own ideas. The possibilities are endless, and the stacked version makes a very stable fabric. (NOTE: Images to follow.) If you need help reading the patterns, you can read about that here.

Ring 3-3-3-3, rw; * chain 4-4, rw; ring 3+3-3-3, rw; repeat from * for desired length.

Variation #1

Ring 3-2-1-1-2-3, rw; * chain 4-4, rw; ring 3+2-1-1-2-3, rw; repeat from * for desired length.

Variation #2

Ring 3-3-3-3, rw; * chain 2-2-2-2, rw; ring 3+3-3-3, repeat from * for desired length.

I think you get the idea here. You can combine any stitch and picot combination, as long as you keep the stitch count the same (12 stitches in the ring, and 8 stitches in the chain).

Corners

Corner options are pretty limited, but it also depends on if your rings or chains will be the outside edge of your project.

Corner Variation #1 - Inside corners

After completing at least one repeat of the above edging variation, work one more chain. For the next ring, join the first picot to the corresponding picot of the previous ring, and join the 2nd picot into the 2nd picot of the previous ring. Make one more chain, and one more ring, joining the first picot to the corresponding picot of the previous ring, and the 2nd picot to the joined picot of the last two rings. Complete this ring as before. Continue with a chain and ring as determined by your edging.

NOTE: For this corner, the ring will join next to each other, and in the top center of each ring. If you used the 2nd variation above, you will have to fudge the picots a little bit for it to work out.

Corner Variation #2 - Outside corners

After completing at least one repeat of the above edging variation, immediately work another ring, joining the 1st picot to the last picot of the previous ring. Work one more ring, joining as before. Resume edging pattern with a chain, joining the 1st two picots to the last two picots of the previous chain, then ring, as usual.

NOTE: When coming out of the corner, I keep making the mistake of joining to the top/center picot of the previous ring, instead of the last picot. Make sure you keep an eye on which picot you're joining to.

Stacking

Variation #1

Row 1: Using your choice of the main pattern from above, work a length as desired.

Row 2: Using the same pattern, repeat Row 1, joining the picots in the rings to the corresponding rings of the previous row.

You can be done after two rows, or you can repeat Row 1, joining the center picot of the chain to the center picot of the chain in the previous row. Then, repeat Row 2, joining it in the same way to Row 3.

For corners, if you used Inside Corners for the first row, used Outside corners for the 2nd row, and vice versa.

Variation #2

Work the same as Variation #1, but this time, join the ring picots to the chains. Repeat for as many rows as desired.

For corners, see Variation #1.

Variation #3

This is the one I used for my Tatted Yoke.

I did Row 1 & 2 as in Variation #1, then Row 3 as in Variation #2, and Row 4 as in Variation #1 again.

For corners, see Variation #1.

Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

Work Log - 21 October, Saturday

Spinning Skein 3 for the kids' hats is drying. Jacob fleece is drying. Spun 2nd ply for knitted ponchos , plyed them, and washed them. Now hanging to dry. Facebook Two posts today . Scheduled one for tomorrow so far, and may just leave it at that. Plan to post 3-4 on each weekday, and 3-4 total during the weekend.
Post a Comment
Read more

Work Log - 23 October, Monday

Spinning Washed the second bucket of Jacob fleece and filmed a reel. Finished spinning the another ply for the yarn for my poncho project . Attempted to film a reel while spinning the 2nd ply, but the app ate the draft, so I have to start over tomorrow. Wound the first skein into a ball. Wound up the 3rd skein into a ball for the kids' hat project . Crocheting Finished the second scarf for the SU scarf project . Just have to weave in ends and finish patterns. Started a hat with the left over yarn, but I don't like it, so I'll probably just put up the rest of the yarn for another day. Social Media Really struggled with trying to get posts onto both Facebook and Intagram at the same time. Have decided to post to Instagram first, because it will automatically post to Facebook, as well. It is supposed to work the other way, too, but it is not working that way.
Post a Comment
Read more

Outlander Inspired Fingerless Mitts

I love fingerless gloves. They're especially handy keeping my hands warm while playing the violin outdoors in the winter. I had crocheted a pair several years ago, but one went by way of the sock trick (you know - you put two in the wash, and only one comes out?). Anyway, around my third time through the Outlander TV series, I started taking more notice of the outfits and accessories the women were wearing. Since I had a need, I decided to have another go at a pair of fingerless gloves, and this is what I came up with. Enjoy! I started by measuring around my palm, at the base of my index and pinky fingers. I measured my right hand, since it's a little bigger. In fact, I couldn't find my tape measure, so my daughter put a piece of washi tape around my hand, then stuck it to a piece of paper. I cast on my stitches until they were the same length, then added two stitches for the seam. Working in a flat piece, I started with about an inch of seed stitch, then separa...
Post a Comment
Read more